| View previous topic :: View next topic |
| Author |
Message |
Todd Renaud
Joined: 21 Oct 2001
Posts: 205
Location: United States, Texas, San Antonio, TX
|
 Posted: Thu Feb 21, 2013 1:45 pm Post subject: Know the official name of grooved machine bolt? |
 |
|
Can't seem to find the "official name" of the bolts that have a groove machined in them at the end of the bolt - commonly found on the areas of the karts (tie rods, pedals, steering columns) that need safety wire per org regulations. These grooves allow the use of the following safety clip (I know where to get these) as shown below:
Anyone a.) know the name and b.) where (bolt house) can I order these types of bolts?
Thanks. |
|
| Back to top |
|
 |
John Matthews
Joined: 04 Dec 2004
Posts: 2013
Location: United States, Michigan, Williamsburg
|
| Posted: Thu Feb 21, 2013 6:48 pm Post subject: |
|
|
Don't know the "official" name of them, they aren't referenced in any of Carroll Smith's books 
But you will probably have to get them from kart suppliers rather than industrial fastener suppliers since I think they come from Italy.
From what I remember Kart Parts Unlimited had both the bolts and safety clips in stock last time I bought fasteners from them. Check with your local kart shop 
Cheers,
_________________
John Matthews
Heartbeat Power, LLC. |
|
| Back to top |
|
|
Todd Renaud
Joined: 21 Oct 2001
Posts: 205
Location: United States, Texas, San Antonio, TX
|
| Posted: Fri Feb 22, 2013 9:10 am Post subject: |
|
|
| John Matthews wrote: | | Don't know the "official" name of them, they aren't referenced in any of Carroll Smith's books , |
Agree with you there. Carroll is the final "say" on these things. Appreciate the reply. |
|
| Back to top |
|
|
Walt Gifford
Joined: 19 Jul 2002
Posts: 4344
Location: United States, South Jerrrsey,
|
| Posted: Fri Feb 22, 2013 12:15 pm Post subject: |
|
|
I think technology is running ahead of nameology. I don't think you'll find them from industrial suppliers. I believe they are made on a limited production basis by kart manufactures.
Some of your finer kart shops have drilled bolts for use with cotter pins if you don't like drilling the bolts yourself.
Gif 
_________________
FAA certified jet engine and aircraft technician
Nicholson Speedway class champion 2001
Yamaha KT100 Service Center
40 years karting experience |
|
| Back to top |
|
|
Benn Herr
Joined: 18 Jul 2001
Posts: 1584
|
|
| Back to top |
|
|
Bill Martin
Joined: 20 Jul 2001
Posts: 412
Location: United States, California, Escondido
|
| Posted: Sun Mar 03, 2013 11:38 am Post subject: |
|
|
heh! That would be a learning experience... I've done a few, when no way to get one in a hurry, but I don't recommend it as a career path. Works much better if you can grind the groove with a tool post grinder.
-bill
_________________
Bill Martin |
|
| Back to top |
|
|
John Mulvihill
Joined: 14 Oct 2001
Posts: 1149
Location: United States, New York,
|
| Posted: Mon Mar 04, 2013 10:25 am Post subject: |
|
|
I believe that the proper term is "@#$%^ing bolt that the clip fell off of", or at least that's what I've heard in safety tech.
John
_________________
I bowl overhand.......... |
|
| Back to top |
|
|
Benn Herr
Joined: 18 Jul 2001
Posts: 1584
|
|
| Back to top |
|
|
Chris Reinhardt
Joined: 29 Aug 2002
Posts: 2951
Location: United States, New York, Ossining
|
|
| Back to top |
|
|
John Matthews
Joined: 04 Dec 2004
Posts: 2013
Location: United States, Michigan, Williamsburg
|
| Posted: Tue Mar 05, 2013 5:11 am Post subject: |
|
|
I guess that's because they don't require safety wire in Italy?
You probably don't need it when you change chassis every other race
Seriously folks, drilling for safety wire is only hard the first 10 times. After that you just get it done and move on. It's not worth the extra money as far as I'm concerned and proper safety wire is 1000 times better than those little clips IMHO....
Learn how to select and use fasteners properly, the life you save might be your own
Cheers,
_________________
John Matthews
Heartbeat Power, LLC. |
|
| Back to top |
|
|
Chris Reinhardt
Joined: 29 Aug 2002
Posts: 2951
Location: United States, New York, Ossining
|
| Posted: Tue Mar 05, 2013 10:59 am Post subject: |
|
|
| John Matthews wrote: | Seriously folks, drilling for safety wire is only hard the first 10 times. After that you just get it done and move on. It's not worth the extra money as far as I'm concerned and proper safety wire is 1000 times better than those little clips IMHO....
Learn how to select and use fasteners properly, the life you save might be your own
Cheers, |
A couple of issues come to mind....
Usually if they are not the "USA Type", they're don't have enough thread past the nut to be able to properly drill. So you end up buying a crap load of hardware to replace the stock stuff.
Some organization don't recognize the "USA Type" fastener clips, they have to be safety wired or cotter pinned....
CR
_________________
East Coast Super Kart Series
"This is how we roll!"
www.eastcoastsuperkart.webs.com
CR2 Motorsports
"Home of Cobalt Superkarts"
www.CR2MotorSports.webs.com |
|
| Back to top |
|
|
John Matthews
Joined: 04 Dec 2004
Posts: 2013
Location: United States, Michigan, Williamsburg
|
| Posted: Tue Mar 05, 2013 11:32 am Post subject: |
|
|
Your local tech committee can tell you what's required at your track. From memory all brake hardware, steering hardware and weights should be safety wired. If you're not buying the fancy "USA" type or pre-drilled you're probably looking at ~$25 max to replace all of it plus $10 for drill bits.
Every form of motor racing requires safety wiring AFAIK so learning how to do it right makes sense no matter what.
Read:
You'll be glad you did.
Cheers,
_________________
John Matthews
Heartbeat Power, LLC. |
|
| Back to top |
|
|
|
FAQ
Search
Memberlist
Usergroups
Register
Profile
Login to check your private messages
Login
